What are the steps to configure a switch?
Índice
- What are the steps to configure a switch?
- How do I configure a Cisco switch for home use?
- Do I need to configure my switch?
- How do I assign an IP address to a Cisco switch?
- What are the steps to configure a switch for SSH?
- What is switch configuration?
- Do switches have IP addresses?
- How do I find the IP of my switch?
- How do I change the IP address of my switch?
- How do you set up a Cisco switch?
- How do I enable port security on Cisco switch?
- How do you set up a network switch?
- How do you clear a Cisco switch?
What are the steps to configure a switch?
- Step 1: Inspect your hardware. Check the model number of your shiny new switch. ...
- Step 2: Set up management IP. ...
- Step 3: Check VTP revision number. ...
- Step 4: Configure access ports. ...
- Step 5: Configure trunk ports. ...
- Step 6: Configure access ports. ...
- Step 7: Set up VTY line config.
How do I configure a Cisco switch for home use?
How to configure Cisco switch?
- Initial command prompt "Switch>" appears on the screen.
- Type "enable" next to it and press "Enter".
- This will take you into the "EXEC" mode, also known as the Global Configuration mode.
- Go into configure mode using configure terminal.
- Enter the configuration commands one per line.
Do I need to configure my switch?
Most switches used by small businesses and home offices typically require no configuration -- they're "plug and play." However, it's important to remember that plug and play doesn't always work. In addition, these switches certainly don't offer any troubleshooting, logging, security, or manageability.
How do I assign an IP address to a Cisco switch?
Configure an IP address on a switch
- enter the VLAN 1 configuration mode with the interface vlan 1 global configuration command.
- assign an IP address with the ip address IP_ADDRESS SUBNET_MASK interface subcommand.
- enable the VLAN 1 interface with the no shutdown interface subcommand.
What are the steps to configure a switch for SSH?
Once you enable SSH, you can access it remotely using PuTTY or any other SSH client.
- Setup Management IP. First, make sure you have performed basic network configurations on your switch. ...
- Set hostname and domain-name. ...
- Generate the RSA Keys. ...
- Setup the Line VTY configurations. ...
- Create the username password. ...
- Verify SSH access.
What is switch configuration?
A switch is a layer 2 device used to forward packet from one device to another within the network. It forwards the packet through one of its ports on the basis of destination MAC address and the entry in the MAC table. Following basic commands are used to configure a new switch : 1.
Do switches have IP addresses?
But since the switch does not have the capability to assign IP addresses, the computers connected to it will not be able to communicate with each other. They will get an Automatic Private IP Address (APIPA). You need to assign a static IP address to your computers.
How do I find the IP of my switch?
Type "show running-config" or "show config" and press the "Enter" key. The IP address or addresses assigned to interfaces on the switch are displayed in the command line interface output.
How do I change the IP address of my switch?
On the Nintendo Switch console:
- Select “System Settings” from the HOME Menu of your Nintendo Switch console.
- Select “Internet”, and then “Internet Settings”. ...
- Select your network from the list of networks located under “Registered Networks”.
- Select “Change Settings”, then scroll down and select "IP Address Settings".
How do you set up a Cisco switch?
- Configuring a Cisco 3548 switch is very simple. Connect the Cisco 3548 switch’s console port with the computer’s com port by using the UTP roll over cable. After physical connection, make a HyperTerminal session and give it any name. The com port setting should be Restore Default in the com port’s properties.
How do I enable port security on Cisco switch?
- then assign the IP address to the Cisco Router.
- test the network connection between clients. Ping the PC0 to the Router interface and PC1 to test the connection.
- click on the Cisco Switch.
How do you set up a network switch?
- Steps to Set up a Network Switch With a Router Step 1: Unplug all the power supplies of cable modem, network switch and wireless router. Step 2: Connect your modem to the telephone wire. Step 3: Plug the other end of the Ethernet cable connected with modem into your router’s WAN port.
How do you clear a Cisco switch?
- Clearing out a Cisco switch configuration is always a pain because VLANs are kept in a seperate file from the startup-config (NVRAM). There's two ways to clear a switch back to the factory defaults – the easy way and the REALLY easy way: Hold the "mode" button on the front of the switch for 10 seconds.
